Does Optronics Red Side Marker Light Include a Base and Wiring

Question

Question:

Is the MCL91RK clearance light the same as MCL-91AK? There is no images for the red light. Does it include the base and wire similar to the MCL-91AK amber light? I am refitting a trailer and want the lights to match in appearance.

asked by: Steve

0

Expert Reply:

Trailer light # MCL-91RK includes the red clearance light and chrome housing in addition to the plug. Basically it is exactly like # MCL-91AK except it is red instead of amber so they will match.

expert reply by: Michael H

0

Answer 1

The Mini Thin Line Sealed LED Marker/Clearance Light, #MCL-91AK, will attach to the trailer using 2 screws which are included. I have included a picture showing the mounting holes for you.

view full answer...

Answer 2

You are correct that the Optronics Thin Line Sealed LED Marker/Clearance Light #MCL-91AK that you referenced will require a jumper ground wire to be run to a metal portion of your trailer frame if it is installed on a plastic surface. You will want…

view full answer...

Answer 3

The correct replacement 7-way for your Tundra should be part #HM43385. You can confirm this by examining the connectors under the truck that the connector would plug into. One connector should accept 4 pins, the other three pins. If your connectors…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...