How Tight Should Spindle Nut of Timbren Axle Less Kit be

Question

Question:

Hi there. What size socket is required for the Timbren Axle-Less Trailer Suspension System - 4inch Lift Spindle w/ Brake Flange? Thanks

asked by: David L

0

Expert Reply:

When installing spindle nuts like what comes on the Timbren Axle Less Kit # TASR5200S03 Timbren recommends tightening the nut to 50 ft lbs and then backing off 1/8 turn.

expert reply by: Jameson C

0

Answer 1

You'd have to box the I-frame of the trailer where you want to install the Timbren Axle-Less Trailer Suspension System #TASR5200S03 so that the kit's side brackets can attach to it.

view full answer...

Answer 2

The only axles we offer that have a high enough weight capacity would be the Timbren setup like part #ASR5200S01. This is actually an "axle-less" system that attaches to the trailer frame and provides an axle setup that is somewhat…

view full answer...

Answer 3

We carry the Timbren Axle-Less System rated at 5,200 lbs part #ASR5200S01. The axle-less system mounts to your trailer frame and takes the place of your old axle and springs.#ASR5200S01 is a straight spindle design. Timbren also offers these axles…

view full answer...

Answer 4

A Timbren Axle-Less system or Silent Ride system would definitely upgrade the stock leaf spring set up on any camper or trailer. That being said, there are a couple things to keep in mind when choosing one of these systems.. The Timbren Axle-Less…

view full answer...

Answer 5

To answer your first question, the Timbren Axle-Less Suspension #ASR5200S01 you referenced is compatible with disc brakes that use a 5-bolt mounting flange, the Kodiak Disc Brake Kit #K2HR526D. This is a hub and rotor kit; you will also need Bearing…

view full answer...

Answer 6

There are a number of differences between the Firestone Ride-Rite Air Helper Springs #F2445 and Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88299, starting with fit. While the Air Lift will fit all models of the 2018 Toyota Tundra, the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

How Tight Should Spindle Nut of Timbren Axle Less Kit be

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching