Installation Instructions for Curt Custom, No-Drill Fifth Wheel Bracket Kit for Dodge Ram

Question

Question:

C16419 no instructions in box, no holes line up with holes on frame. Your site says it fits my truck 2008 dodge 2500 crew cab

asked by: Sam A

0

Expert Reply:

The Curt Custom, No-Drill Fifth Wheel Bracket Kit for Dodge Ram # C16419 fits the 2002 - 2008 Dodge 1500 and 2500 Trucks. Excluding the Mega Cab and Overload Springs. We know that you do not have the Mega Cab but If you have the Overload springs they would not fit. That information is from the manufacturer.

I have also linked to the instructions of the # C16419 for you to check out since yours were missing.

expert reply by: Scott S

0

Answer 1

The only fifth wheel rail kits we offer for your 2002 Dodge Ram 3500 long bed are universal style kits like the Reese part #RP30035. For just the L-brackets you'd want the part #RP58314. The Curt kit you mentioned does not fit your truck.

view full answer...

Answer 2

Custom fit brackets do work better in a sense. The installation time is reduced dramatically because custom fit brackets uses as many factory holes as possible so most of the time you do not have to drill any new holes in the truck frame. Part…

view full answer...

Answer 3

Yes, the Pullrite 2700 fits industry standard rails so you could go with Curt Custom, No-Drill Fifth Wheel Bracket Kit for Dodge Ram #C16419 if you just need the brackets. Or for the complete kit you can go with Curt Custom Fifth Wheel Installation…

view full answer...

Answer 4

Yes it looks like the same Curt fifth wheel rail kit part #C16306-204 does fit both a 2018 Ram 1500 6-1/2 foot bed and a 2012 Ram 1500 5-1/2 foot bed.

view full answer...

Answer 5

If you have the industry standard rails like what are pictured in the pic that I attached you would just need the Reese Universal Installation Kit #RP30439 and you would be good. You will want to compare the dimensions of the rails in the picture to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Installation Instructions for Curt Custom, No-Drill Fifth Wheel Bracket Kit for Dodge Ram

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching