Will Tandem Axle Teardrop Trailer Fenders for Boat Trailers Fit 2005 EZ Loader Boat Trailer

Question

Question:

I have an 05 E Z Loader boat trailer and need to replace the fenders. Will your item HP34VR fit this particular trailer ? Is the overall measurement taken at the bottom of your fenders ?

asked by: Larry G

1

Helpful Expert Reply:

In order to find the best fit for replacement fenders you will want to measure the existing fenders on your 2005 EZ Loader boat trailer. Although typically not an exact match, you want to do your best to match the dimensions of your existing fenders. The overall length is taken from the widest point, which is at the bottom in this case.

The overall dimensions for the Tandem Axle Teardrop Trailer Fenders for Boat Trailers - Stainless Steel - 14" Wheels - Qty 2 # HP34VR are 65" long x 9" wide x 15" tall. These are designed for tandem-axle trailers with 14" diameter wheels. Assuming your dimensions are close and you're using 14" wheels this should fit your trailer without any issues.

expert reply by: Robin H

1

Answer 1

There is not a chrome version available of the Tandem Axle Teardrop Trailer Fenders for Boat Trailers - Stainless Steel - 14" Wheels - Qty 2 #HP34VR. That said, the #HP34VR being stainless steel with the PVC coating gives them a nice shine that…

view full answer...

Answer 2

Based on the measurements you provided the Grease Seal #010-180-00 is the closest match we have for you in our inventory. We do not carry and did not see the part number referenced KOK 2611 in searches. To be sure you can always revisit your spindle…

view full answer...

Answer 3

It sounds like you might be looking for the Tandem Axle Teardrop Trailer Fenders for Boat Trailers - Stainless Steel - 14" Wheels - Qty 2 #HP34VR. This fender is made from stainless steel and has the same dimensions you mentioned- 9" wide x…

view full answer...

Answer 4

I have a solution for you, but we don't have a grease seal that has those exact measurements. With that said, the Grease Seal #010-180-00 is a double lip seal (which are common on boat trailers) and has ID: 1.68" and OD: 2.33". It's…

view full answer...

Answer 5

I have no way of looking up which actuator your boat trailer was equipped with, as the trailer manufacturers don't make that database information public. If your Ranger boat trailer uses the Dexter DX7.5 Disc Brake Actuator, the #DX99FR would be…

view full answer...

Answer 6

Yes, there is a bushing inside the equalizer kit part #AP233 that you referenced.

view full answer...

Answer 7

The main difference between The Dexter Inner Membrane #DX99FR and The Dexter inner Membrane #DX39FR is that the #DX99FR is for a tandem axle with disc brake setup. The #DX39FR is for a single axle with disc brake setup. Both Dexter membranes have a 2…

view full answer...

Answer 8

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 9

The thickness of the Shackle Strap #TRSL225 that you referenced 3/16 inches. The thickest shackle we offer in the length of 2-1/4 inches is the part #018-024-01 which is 1/2 inch thick. I know that sounds almost too thick to be true, but I've…

view full answer...

Answer 10

If the shackles are touching the frame when using the Road Armor Shock Absorbing Equalizer Kit #LC696740 it does indicate the shackles are too long, and since you mentioned you had 3-1/8" shackles, you can use shorter ones which can help. I…

view full answer...

Answer 11

The shackle straps of the #AP233 are 2-1/4 inches in length from bolt hole center to bolt hole center.

view full answer...

Answer 12

As long as the new equalizer has the same hole spacing as the existing equalizer, it'll work just fine. You'll also want to make sure the height of the equalizer is also the same. Put a ruler across the center of the two bottom bolt holes,…

view full answer...