Mud Guards For A 2003 Toyota Tundra SR5 With Fender Flares

Question

Question:

Do you make an exact fir mud guard set for an 03 tundra SR5?

asked by: Mark F

1

Helpful Expert Reply:

The only mud flaps I offer for you 2003 Toyota Tundra SR5 with add-on fender flares that is NOT mounted to your trailer hitch are the Truck Mud Flaps - Black Rubber - Teardrop Shape - 10" Wide x 18" Tall - Qty 2, part # 337B1018LSP, and the Truck Mud Flaps - Black Rubber - 12" Wide x 18" Tall - Qty 2, part # 337B1218LSP. These mud guards are will fit your truck, but they are a universal fit, so you will most likely have to do some altering to make them fit.

I have included product description links and a video review link below.

expert reply by: Mark Smith

1

Answer 1

The Buyers Products #337B1018LSP do not come with any mounting hardware, since the method of mounting is going to vary from vehicle to vehicle. Ideally you will use the factory fasteners on your vehicle to secure it into place and locally sourced…

view full answer...

Answer 2

I cannot confirm what the harness you have pictured is for. However, it is not a trailer wiring harness. If you'd like to add a 4-way to your 2019 Chevrolet Express Van (assuming you don't have the factory tow package, of course), then you…

view full answer...

Answer 3

For the 2019 Chevy Express Van 2500 without a towing package, you will need the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #118392 which will give you a 4-pole to start with if you don't already have one. Then…

view full answer...

Answer 4

Thanks for the photo and let's start with the correct 4-way for your 2020 Chevy Express 2500, which is the T-One Vehicle Wiring Harness #118392. As you can see by the cut out of the linked installation instructions I added, you will connect the…

view full answer...

Answer 5

You have to wire a separate 12 volt power wire for the 7-way adapter as it would draw considerably more than what the power wire of your 4-way kit is capable of. The 4-way's power wire will be in use at all times so you couldn't swap between…

view full answer...

Answer 6

I spoke with a Buyers Products representative about the Fender Guard Mud Flaps - Black ThermoFlex - 10" Wide x 20" Tall - Qty 2, part #337B1020PPB. They emailed me a dimensional drawing of one of these mud flaps. They matched the ones you…

view full answer...

Answer 7

When you install the RockTamers part #ERT00108 you will want the flaps to hang 3-4 inches from the ground for proper ground clearance. You would want to take this measurement with the truck loaded and then use the pre-cut lines as a guide for making…

view full answer...

Answer 8

I haven't heard of the Curt 7-way tester not working with OEM brake controllers. There was a Tekonsha tester that had problems with Dodge and GM trucks so it is possible. We have been able to confirm that the Pollak 7-Way to RV Socket LED Circuit…

view full answer...

Answer 9

I reached out to the manufacturer, Buyers Products, who told me the pre-drilled mounting holes are 1/2" wide x 3/8" tall for their 12 x 18 mud flaps, which are the following part number: - Truck Mud Flaps - Black Rubber - 12" Wide x…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...