Lift Kit that Fits 2020 Rockwood 2508 Mini Lite

Question

Question:

it's a dexter 3k axle.

asked by: Anthony E

0

Expert Reply:

Can you check the axles and let me know what brand, capacity, and style they are?

expert reply by: Jameson C

0

Anthony E.

5/4/2022

it's a dexter 3k axle.

Reply

Jameson C.

5/4/2022

Thank you for that info, based on that you'd need the Torflex part # K71-707-01 which will give you a lift of 2-5/8 inches.

Reply

Answer 1

The Dexter Axle Torflex axles are basically broken up into the following categories: #9 - 1,000 - 2,200 lb #10 - 2,300 - 4,000 lb #11 - 4,100 - 6,000 lb #12 - 5,500 - 7,200 lb Based off of your 2004 R-Vision Trail-Lite Model 8306S being a tandem axle…

view full answer...

Answer 2

We can help you out here, and first, thanks so much for the photo it was super helpful. And based on that I can tell you that your tandem axle trailer with #10 Torflex axles is absolutely compatible with the Dexter lift kit: - Torflex Lift Kit -…

view full answer...

Answer 3

The best way to jack up a boat trailer with torsion axles, or straight axles for that matter, is to use a trailer jack that is rated high enough for the weight of the trailer at the point the jack is installed. Going with a higher capacity than…

view full answer...

Answer 4

The wires on the Dexter Nev-R-Adjust Electric Trailer Brake Assembly #K23-478-00 are 12 gauge wires. We recommend using 10 Gauge Wire #10-1-1 from the trailer 7-Way connector to the brakes though to help ensure enough power gets to them.

view full answer...

Answer 5

When installing the Torflex Lift Kit #K71-707-02 for the #10 Dexter axles on your 2022 Forest River Rockwood Mini Lite travel trailer you will want to follow the manufacturer instructions for raising your entire trailer off the ground. This is…

view full answer...

Answer 6

Thanks for the picture of your trailer light lens. Based on seeing that we do know that the part #OPT47FR is the correct replacement.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...