Which Grease is Used on Lippert Trailer Axles

Question

Question:

I have lippert 4400 lb axles on my fifth wheel and was wondering what grease lippert uses for there wheel bearings?

asked by: William S

0

Expert Reply:

According to Lippert they use Lithium Complex grease on their 2k-7k axles. This means you can use a Lithium Complex grease like the LubriMatic LMX Industrial Strength Grease - 14 oz. Cartridge # L11390 for your bearings.

expert reply by: Robin H

0

Answer 1

It should be getting close to 12 volts if the power output is set to the maximum on the brake controller. Some brake controllers will not work properly if they are titled or turned to the side or if it has a leveler knob that is not level. Check…

view full answer...

Answer 2

I would start by using a circuit tester, item #PTW2993 if needed, to check the wiring going to and coming from the brake controller. There are 4 wires that will need to be checked. White - Ground Red - Stoplight Switch Black - 12 Volt Constant Power…

view full answer...

Answer 3

Usually when you replace parts that get lubricated, you clean all of the existing grease first before adding any new grease, just in case there is a compatibility issue. Since you are using Dexter axles and replacing components with Dexter parts, the…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

I have a solution for you, but I don't recommend using white lithium grease on your wheel bearings, since it's more of a general lubricant and there are much better products specifically designed for wheel bearings. Instead, I recommend using…

view full answer...

Answer 7

Typically as long as you're staying at or below 200 degrees you're doing fine. The fact that one hub is hotter than the other could just mean that you had more weight over that one hub or that the brake setting was more aggressive on that hub…

view full answer...

Answer 8

Standard tapered trailer wheel bearings are recommended to be re-packed with fresh bearing grease about every year or every 12,000 miles under normal use. In certain conditions this interval could be shorter, such as if you routinely tow the trailer…

view full answer...

Answer 9

When adding grease like the #L11390 you want to pump the grease slowly and rotate the hub. You will continue to pump the grease until you begin to see grease come out of the front. If you're replacing old grease, you will continue to pump until…

view full answer...

Answer 10

There are many reasons why one of your hubs is running hotter than the other. We usually recommend that you work on both hubs at the same time when you are trouble shooting, this way you know that the same work was done on both hubs. I would change…

view full answer...

Answer 11

The Sealed Oval Trailer Stop, Turn and Tail Light, item #ST70RB, uses an 1157 automotive style bulb with two filaments. The bright filament is rated at 21 watts and the dim filament is rated at 5 to 6 watts. With the filament wattage, we can…

view full answer...

Answer 12

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Which Grease is Used on Lippert Trailer Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching