Replacement Hitch Bolt And Lock Washer For A SoftRide Bike Rack

Question

Question:

What lock fits this hitch bolt? I lost key for my original and had to have it drilled out. Now looking to replace the lock that fits over the pin side of this bolt.

asked by: Bernie

0

Expert Reply:

The Replacement Anti-Rattle Hitch Bolt and Lock Washer for Softride Bike Racks # SR19696 is the correct replacement anti-rattle hitch bolt and lock washer for your SoftRide bike rack, like the Softride Dura Parallelogram 4 Bike Rack # SR26247(no longer available from manufacturer), however there isn't a lock replacement available, unfortunately.

Instead, I recommend a new system like the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches # 63232. This will fit on class II 2" x 2" hitch accessories, and will help prevent theft and secure your bike rack.

expert reply by: Bryce D

0

SoftRide Hitch Bolt Replacement
(click to enlarge)

Answer 1

The Replacement Anti-Rattle Hitch Bolt and Lock Washer for Softride Bike Racks - 1-1/4" Hitches #SR19696 is what you need. This is a direct replacement for your bike rack.

view full answer...

Answer 2

The size of the hex on the Replacement Anti-Rattle Hitch Bolt #SR19696 that you referenced is 22 mm.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...