What Locking Hitch Pin Fits My Gen-Y Torsion 2-Ball Mount # 325-GH-1025?

Question

Question:

I'm trying to make sure no one steals my Gen-Y Torsion 2-ball 325-GH-1025. What hitch lock fits?

asked by: Juan G

0

Expert Reply:

For a great hitch lock that fits your Gen-Y Torsion 2-Ball Mount - 2" Hitch # 325-GH-1025, I recommend theCurt Trailer Hitch Receiver Lock - 2" and 2-1/2" Hitches - Stainless Steel # C23519. This lock is compatible with 2" hitches and has a 5/8" pin diameter.

expert reply by: Bob C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

Hi Bill, The Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA92-00-0450 has a tongue weight range of 200lbs - 450lbs so you'd be right around the middle of the capacity when loaded, making this a great choice. This doesn't come with…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

On the Jeep Wrangler and Jeep Truck models the steering wheel does not actually lock with the ignition in the off position, it just has a loss of power steering-which is likely what you're experiencing. Jeep removed the steering wheel lock from…

view full answer...

Answer 8

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 9

Choosing the correct rear suspension enhancement for your 2022 Jeep Gladiator will depend on how much sag you are actually getting and if you want to have something that is adjustable or not. The SumoSprings Solo Custom Helper Springs #SS62XR will be…

view full answer...

Answer 10

Hey Dave, In my opinion the etrailer Invisible Base Plate Kit #e98948 is going to be the stronger option compared to the Blue Ox Base Plate Kit #BLU53FR. Blue Ox started adding safety cables to their baseplate kits as a last resort backup in the…

view full answer...

Answer 11

Hi Dave, The etrailer Invisible Base Plate Kit #e98948 and Blue Ox Base Plate Kit #BLU53FR are designed slightly different, but both are compatible fits for your 2023 Jeep Gladiator. The #e98948 is going to be an easier installation since you…

view full answer...

Answer 12

The Westlake would be by first choice like tire part #LHWL410. This is actually a Load Range G so the capacity is 4,400-lb max load at 110 psi .This Westlake tire has a speed rating of 81 mph and also has a great warranty as well. The Taskmaster…

view full answer...