Bearing Kit for the Roadmaster RM 3477 Tow Dolly

Question

Question:

Do you have wheel bearings and seals for the Roadmaster RM 3477

asked by: Mark S

0

Expert Reply:

Yes, we do. The correct bearing kit for the Roadmaster RM 3477 Tow Dolly item # RM-2050-1 is the Hub Bearing Kit item # BK2-100.

For new bearing grease the very best choice is LMX Red. This formula withstands pressure, high temperatures and water better than others. You can order it in 14-ounce cartridges as item # L11390 along with grease gun item # L30416.

expert reply by: Jerred H

0

Answer 1

The correct replacement hub/drum for the Roadmaster Tow Dolly with Electric Brakes (RM3477) part #RM-2050-1 is the Dexter Trailer Hub and Drum Assembly part #84546UC3-EZ. This is a complete kit and what I recommend using to get back up and running.…

view full answer...

Answer 2

In regards to the Roadmaster Tow Dolly with Electric Brakes (RM3477) part #RM-2050-1, the correct replacement spindle is part #RM63FR, the correct replacement braking assemblies are part #RM-4701-R for the passenger side and part #RM-4701-L for the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...