Recommended Replacement for Glo Brite 126R/126Y Side Marker Lights

Question

Question:

TML GLO BRITE 126R/126Y 3 and 7/8 by 1 and 3/8 LED We need the clearance/marker lights listed above in LED.

asked by: Mark &

0

Expert Reply:

The Optronics Trailer Clearance or Side Marker Light part # MC44RB for red or part # MC44AB for amber work great to replace the old discontinued Glo Brite 126R/126Y. They are not the exact same but very similar in design and dimensions. They feature a very simple two wire install.

expert reply by: Conner L

0

Answer 1

To replace your GloBrite 126 marker lights you can use the #MC44RB for the red light and the #MC44AB for the amber light. Both of these lights are 2 wire lights and will work well on your cargo trailer. And yes, we can ship this particular product to…

view full answer...

Answer 2

Glo Brite is indeed out of business, but we may have an amber LED assembly that will work nicely as a replacement to your broken unit. The closest LED assembly we have available to the measurements you provided is with the Command LED Clearance or…

view full answer...

Answer 3

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 4

We have the Peterson Red Flush Mount Clearance Light with Chrome Plating, 126R #425000 to replace your red lights and the Peterson Amber Flush Mount Clearance Light with Chrome Plating, 126A #424800 to replace your amber (yellow/orange) lights. If…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...