Is the Thinline LED Trailer Tail Light a Single Light

Question

Question:

I was wondering is part number stl69rcb is the pricing for a pair or single light

asked by: James

0

Expert Reply:

The Thinline LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 11 Diodes - Clear Lens # STL69RCB is a single light. If you needed two of these lights you would have to order a quantity of two.

expert reply by: Robin H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 4

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 7

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...