Inside And Outside Diameter Of The Bristol Double RV Waste Valves Hubs

Question

Question:

What is the od and id of the inlets ?

asked by: Steve A

0

Expert Reply:

The inside diameter of the Bristol Double RV Waste Valves # 34466NDHR19AAA is 3-1/2" and the outside is 4". Since these are hubs they'll slide over your 3" ID (3.5" OD) waste pipe.

expert reply by: Kevin C

0

Answer 1

The Bristol Double RV Waste Valves, #34466NDHR19AAA has an overall measurement of 11-7/8" from edge to edge with a 9" measurement between the outer edge of each waste gate.

view full answer...

Answer 2

ABS plastic like what the Bristol Double RV Waste Valves #34466NDHR19AAA you referenced is made of can be glued to ABS plastic but plumbing codes won't allow you to glue it to PVC. You can solvent weld this to ABS plastic though!

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...