Will The Curt Hitch Require Air Dam Removal On A 2013 Toyota Corolla S

Question

Question:

Will your curt hitch fit my 2013 Corolla s without removal of the rear air dam

asked by: Ravon D

0

Expert Reply:

When installing The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4 inch # C11265 you will not have to remove the rear air dam it only has three installation steps. If present, remove existing bolts from tow loops. Then you would raise the hitch into position and align the holes in the side plates, secure the hitch with the hardware provided. Finally you torque down all hardware.

I will attach an installation video below.

expert reply by: Noah E

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver part #C11265 is what I recommend for a 2017 Toyota Corolla. It has a 1-1/4" opening for use with hitch mounted accessories like bike racks and cargo carriers. It has a 200 lb tongue weight rating which will be…

view full answer...

Answer 3

With Curt trailer hitch #C11265 installed on your 2016 Toyota Corolla the distance from the ground to the bottom of the hitch will be approximately 9-1/4 inches. It measures 10-3/4 inches from the ground to the top of the receiver opening. If you…

view full answer...

Answer 4

The bolt holes on the Curt Trailer Hitch Receiver part #C11265 are spaced 40.85" left to right but this is irreverent as it is a custom fit option designed specifically for a 2012 Toyota Corolla so if this is what you have there won't be any…

view full answer...

Answer 5

I would be happy to help! From the center of the hitch pin hole of the Curt Trailer Hitch Receiver #C11265 you were looking at to the front of the receiver is 2", and to the rear of the receiver is 3-1/2" as you can see in the included…

view full answer...

Answer 6

The weight of the Curt hitch #C11265 that you referenced is 27 lbs. The overall width is 47-1/2 inches.

view full answer...

Answer 7

I went out to the warehouse and found from the top of the mounting brackets to the bottom of the safety chain loops (which will be the lowest thing on the hitch) of the Curt #C11265 is about 7-5/8 inches. If you check out the linked instructions or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...