How to Get etrailer Coupler & Hitch Locks Keyed Alike

Question

Question:

Is there a Keyed alike lock set that includes one each of the following items? E98890 E98880 E98887

asked by: Doug P

0

Expert Reply:

You can get those locks all keyed alike, but there isn't a set with all three together. Instead, what you'd do is go to the product pages of each, and on those product pages there is a drop-down box that says "Keyed Alike?" and you'd select the keyed alike option for each lock:

- etrailer Trailer Hitch Receiver Lock for 2" Hitches # e98880

- etrailer Surge Brake Coupler Lock - 2-1/2" Span - 1/4" Diameter # e98887

- etrailer Trailer Coupler Latch Lock - 7/8" Span - 1/4" Diameter # e98890

When you do that, you will get all three locks keyed alike.

expert reply by: Kyle S

0

Answer 1

Yes, the Trailer Coupler Lock #e98887 that you referenced will work with a UFP A-60 coupler lock. The product picture for this lock shows it being used on an A-60. I attached a review video for you to check out as well.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Sorry, John. We do not have any Rhino-Rack keys for the lock code 290. Typically the best route to go is changing all your Rhino-Rack lock cores to their more premium keys so you can have all your accessories keyed alike as well. Here is a list of…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 11

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...