Correct Curt 5th Wheel Frame Brackets for 2002 Ford F-250/F-350

Question

Question:

Will this fit my 2002 f250 ford long box?

asked by: Mike

0

Expert Reply:

The correct Curt fifth wheel frame brackets for a 2002 Ford F-250 is the Curt Custom Fifth Wheel Bracket Kit for Ford F250 and F350 part # C16443, so yes these are the right ones.

expert reply by: Conner L

0

Answer 1

Hi Zachary, Most 5th wheel trailer hitches all follow an industry standard spacing of 22" from center to center of the rails. If you measure your current rails from center to center then and get 22" then we know you have industry…

view full answer...

Answer 2

For a 2003 Ford F-350 you'll need the Curt Custom Fifth Wheel Installation Kit for Ford F250 and F350 #C16443-204 in order to mount your Curt Q20 5th Wheel Hitch #C16130.

view full answer...

Answer 3

We have what you need and it will work with both hitches. You will not need to change the above bed rails for your 1999 Ford F-350 Super Duty if you install ISR (Industry Standard Rails) which pretty much the only currently available option. Any…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 6

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Correct Curt 5th Wheel Frame Brackets for 2002 Ford F-250/F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching