Demco 5th Wheel Adapter for Ford Puck System

Question

Question:

I currently have a Demco slider 5th wheel hitch with factory adapter top plate for a chevy 2500. Will this adapter and slider work with a Ford F450 with the factory puck system?

asked by: Ryan M

0

Expert Reply:

The Demco Slider will work in your 2019 Ford F-450 Super Duty but you will need the Demco 5th Wheel Rail Adapter for Ford OEM 5th Wheel Towing Prep Package - 25,000 lbs item # DM6175. This will allow you to attach your slider to the different puck system that is in the F-450. Chevy uses a different system.

expert reply by: Jerred H

0

Answer 1

The main issue most people have with connecting to a 5th wheel using the Demco Autoslide 5th Wheel Trailer Hitch 18K #DM8550034 or 21K #DM8550035 is the hitch needs to be connected and disconnected in a straight line. This is necessary since the…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 6

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 7

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 8

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 9

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

I recommend using a Lube Plate #16721 over covering the Demco Recon 5th Wheel Trailer Hitch #DM8550043 in Grease #L74FR. The lube plate is much cleaner and you will not have to constantly clean off the dirt and apply new grease over time.

view full answer...