9/16" x 18 Lug Nut Options For A Coachman Motorhome

Question

Question:

I am seeking a jam nut 9/16 x 18 thread to replace a Versa-liner for my Coachman Motoorhome on a Ford E-350 chassis.

asked by: Jack W

0

Expert Reply:

The closest we have to the 9-1/6" x 18 jam nut you need, is the Trailer Wheel Lug Nut # 6-53.

We do also carry the Lionshead Trailer Wheel Lug Nut # LHLR110, which also has the 9/16" x18 threads per inch.

expert reply by: Bryce D

0

Answer 1

The Dexter Trailer Hub and Drum Assembly, part #8-174-5UC3, includes the lug nuts and rim clamps that hold the wheel on to the hub. The lug nuts are part #916N and have a 9/16-inch fine thread. The replacement stud that is installed in the hub…

view full answer...

Answer 2

You can certainly use stainless steel lug nuts like the Kodiak #KALN1375S that you referenced on aluminum trailer wheels. Typically the only precaution you would need to take with aluminum wheels is making sure you get lug nuts that are bit longer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 10

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...