Powered A-Frame Trailer Jack for 2010 Dutchman Sport 26B-DSL

Question

Question:

Will this LC285318 fit a 2010 Dutchman Sport 26B-DSL.

asked by: Ron T

0

Expert Reply:

The Lippert Components # LC285318 uses a standard 3 inch on center bolt pattern. If the hole in your A-frame will accommodate those dimensions, and the tongue weight of your trailer is not greater than its 3,500 lb capacity, the # LC285318 will work for you.

I have found that when it comes to powered jacks, overkill is a good thing. Getting the highest rated jack possible will result in quicker operation and longer life. I really like the Stromberg Carlson # SC63VR tongue jack as it is rated for 4500 pounds of lift and have a clutch that prevents the jack from from being over extended or retracted. It also has a drop-foot which can give you an additional 5 inches of lift if needed.

expert reply by: Mike L

0

Answer 1

Since you are limiting your trailer to 10000lbs, and the average tongue weight is 10-15% of the trailer weight, you are looking at 1000-1500lbs tongue weight. With that said it is a good idea to use a jack with a larger capacity as it will be able…

view full answer...

Answer 2

With just a single one of the Lippert Components High-Speed Power Stabilizer Jacks #LC298707 installed on your trailer you'll get a lot of benefit. You'll be able to level and stabilize the jack and can use your crank jack out on the front of…

view full answer...

Answer 3

The circuit breaker of the Ultra-Fab Electric A-Frame Jack #UF38-944017 is designed to prevent the motor from drawing too much amperage and damaging itself. If you were to lower the jack all the way and then keep holding the button you eventually…

view full answer...

Answer 4

While your frustration is understandable and we have a solution for you, I wouldn't be able to tell you with absolute certainty that using the Stromberg Carlson Electric Trailer Jack #JET-3755 will stop your tailgate from hitting the jack. The…

view full answer...

Answer 5

I have a replacement jack option for you, but the lower jack assembly 87460 you mentioned for your Husky Brute Jack HB4500 has been discontinued as it was for the older model jacks. Since your lower jack assembly is damaged you will need to replace…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 9

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...