Replacement Drive Pin For Lippert Landing Gear VMC900R

Question

Question:

Looking for a replacement drive pin for landing gear leg, leg part number is vmc900r-231185

asked by: Wes J

0

Expert Reply:

For your Lippert Landing Gear Leg VMC900R, you can use the Lead Jack Repair Kit for Stromberg Carlson Landing Gear # LG-146059 for the lead leg, or # LG-146060 for the follow leg. We do not sell the the drive pin individually, it is only available in the kit.

expert reply by: Bryce D

0

Answer 1

Yes, I attached a diagram you can use to install the #LC146059 that you referenced.

view full answer...

Answer 2

I have a solution for you. First, though, to replace the gearbox for your Atwood 75721, you'll need to replace the motor along with the gearbox since there aren't any gearboxes made for that motor any longer. As you mentioned, due to the age…

view full answer...

Answer 3

From what it looks like, the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear #LC146059 would work on your landing gear, but without knowing the brand and capacity it's tough to confirm this. If you can find any identifying marks…

view full answer...

Answer 4

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs item #LG-142178 you were looking at is the correct replacement motor for the discontinued Atwood 75721. The Gearbox for Venture Electric 5th Wheel RV Landing Gear…

view full answer...

Answer 5

Though I could not find anything about the T46059 repair kit you referenced, but odds are the jack isn't rated high enough for the weight of your trailer. Or there is more than just the gears that need to be replaced. What you will probably want…

view full answer...

Answer 6

I attached a picture of the pins that are on the back of the display of the Replacement Auto Level Control Panel for the #LC675817. I'd take some sandpaper and rough up the pins till they are down to bare metal (assuming corrosion is there) and…

view full answer...

Answer 7

If you're getting a RR or LR fault code with your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC358590 or #LC675817, then that is indicating that there is an error at that specific jack (right rear /…

view full answer...

Answer 8

We do have a replacement motor for the lead leg of the Lippert Ground Control kit you have on your 2016 Reflection 27RL with the part #LC343758 but it sounds like you'd rather do the entire leg assembly with part #LC305340. Since it's a new…

view full answer...

Answer 9

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 10

The left front jack error code ("LF) you are getting on your Lippert Ground Control System like #LC675817 can be triggered by a few different things. The first, which it seems you may have already ruled out, is that the system is for whatever…

view full answer...

Answer 11

On the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set #LC358590 the best thing to do to check you level is to recalibrate your system. You do this by resetting your zero point. See the attached…

view full answer...

Answer 12

You can upgrade the Lippert Ground Control 3.0 4-Point Set #LC358590 to the 6-Point Set #LC675817 later on but you will need to replace the control module to part #LC346005 as well as add the Left Rear Leg #LC342610 and Right Rear Leg #LC428493 and…

view full answer...

Replacement Drive Pin For Lippert Landing Gear VMC900R

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching