InfiniteRule Locking Hitch Pin for 32k Gen-Y Ball Mount

Question

Question:

I was not able to find an infinite role lock pin set for a gen -y 32k. Is this something you carry? Thank you

asked by: Amy

0

Expert Reply:

We do have the locking hitch pin for the Gen-Y 32k kits with the part # 34061080-D. This just a single hitch pin.

expert reply by: Jameson C

0

Answer 1

We do have a way for you to lock your ball mount to your hitch receiver but unfortunately, the Blue Ox #BX88212 is not able to be keyed alike. For another solution,our etrailer.com lock #e98881 fits 2-1/2 inch Class V hitch receivers and can be keyed…

view full answer...

Answer 2

The pins that hold the ball mount attachment into the vertical openings of the #325-GH-315 have a span of 3-1/2 inches and a diameter of 5/8 inch so for a hitch lock that would work with this you'd want the Draw Tite part #BD580412.

view full answer...

Answer 3

If you are looking for a quick and easy plug and play wiring to get your 2021 Jeep Wrangler JL set up to be flat towed behind an RV, then the Curt #C96JR will not require a wire to the battery. This will plug in behind the tail lights and then follow…

view full answer...

Answer 4

If you are going to use a riser I recommend the Gen-Y Stacked Receivers #325-GH-304 placed in the rise position. This will allow you to place the Roadmaster Hitch Mounted Spare Tire Carrier #RM-195225 in a higher position on your 2020 Forest River…

view full answer...

Answer 5

Hitch accessories end up being mostly secured horizontally in trailer hitches by the tongue weight of the accessory instead of by the hitch pin which is why hitch pin locks like the #e98881 are not not rated for shear strength. At some point it would…

view full answer...

Answer 6

We do have something like that. The Lippert Spare Tire Winch with Offset Cable #LC159056 use the Crank Extension for Lippert Spare Tire Winch Assemblies #LC1315411 which attaches to the winch. You would then use the Replacement Crank Handle for…

view full answer...

Answer 7

We have precisely what you need for an adjustable ball mount that fits your 2-1/2 inch hitch and gives you up to 8 inches of drop. The ball mount is from BulletProof Hitches and is the following part number: - BulletProof Hitches 2-Ball Mount for…

view full answer...

Answer 8

When you receive your InfiniteRule Hitch Lock #34061073-D you will want to record the key number for the lock. With this key number you will be able to contact InfiniteRule for a set of replacement keys. If you have already lost both keys you may be…

view full answer...

Answer 9

The correct rear TorkLift Tie-Downs for the TorkLift SuperHitch Original Trailer Hitch Receiver #TLD1109 installed on your Ram 2500 is the Kit #TLR3507, which install directly to the side plates as you can see in the attached photo. With a standard…

view full answer...

Answer 10

Going with a higher rated trailer hitch than the weight capacity of your vehicle does not give you additional capacity. With any towing setup you are limited by the lowest rated component as the overall capacity. This Torklift hitch part #TLD1109-30…

view full answer...

Answer 11

Yes, the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TLD1109-30 will fit your 2019 RAM 2500 Power Wagon with the 6-1/2' bed. According to the installation instructions no modification of the spare tire location/support is needed. The…

view full answer...

Answer 12

You can use the Pollack #PK11700 to install on your gooseneck trailer and create a 7 way plug capable of fitting on the 7 pole round plug that is on a semi tractor trailer truck. For the wiring you can use the Deka Jacketed 7 Wire #DW04914-1 which is…

view full answer...

InfiniteRule Locking Hitch Pin for 32k Gen-Y Ball Mount

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching