US Made Swivel Side Mount Trailer Jack

Question

Question:

Where is this jack made? Part number TJP-2002S-B

asked by: Cindy V

0

Expert Reply:

The etrailer brand # TJP-2002S-B is manufactured in China.

We do offer some side mount trailer jacks from Dutton-Lainson that are manufactured in the USA. They don't offer a pipe mount jack, but they do offer a swivel pin mounted jack which would be much more stable. I'd recommend the part # DL22339 1700 lb capacity bolt-on jack. The jack also provides a caster to make maneuvering your trailer around while its being stored much easier. The jack is compatible with frame members that are 3 to 5 inches in height.

expert reply by: Mike L

0

Answer 1

I went to our warehouse to provide you a few measurements of the Pro Series pipe mount swivel jack #PS1401080303. The length of the entire swivel jack in the retracted position is 26-3/4 inches. The foot plate is 3-3/4 inches wide and 7-1/2 inches…

view full answer...

Answer 2

If you have a 2017 Toyota Tacoma with the tow package/factory 7-way yes it is pre-wired for a brake controller. For a brake controller I recommend the Prodigy P3 Brake Controller part #90195. This is our best selling brake controller because of how…

view full answer...

Answer 3

To wire your vehicle battery 12V to charge a trailer battery, I recommend using a 40 amp In-Line Circuit Breaker - Perpendicular Mount Bracket #9510 along with #10-1-1 to wire your trailer connection. In order not to drain your vehicle battery, I…

view full answer...

Answer 4

First, you can connect the 12 volt circuit directly to the trailer battery. However, the wiring in the trailer wiring package is not able to charge up the battery, it can only maintain its current charge level. To up charge the battery, you would…

view full answer...

Answer 5

You will need a battery isolator, like Battery Isolation Solenoid, part #PK5231201, if you plan on leaving the trailer connected to the truck when the truck is off. If you unplug the 7-Way, the trailer battery cannot drain the truck battery. If you…

view full answer...

Answer 6

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 7

While unlikely, it is certainly possible that the trailer battery could backfeed to your vehicle's battery when hooked up under the scenario you described. To make sure this doesn't happen all you need to do is add a single diode like the…

view full answer...

Answer 8

Your 7 Pin connector should be active, especially if it was factory installed. You can test the connector with a circuit tester like our #PTW2992 when the vehicle is on. Then shut it off and test again to see if your connector is still drawing power…

view full answer...

Answer 9

Yes, the photo you attached shows that your 2017 Tacoma has the factory rail system in the truck bed. The Adarac Aluminum Series Custom Truck Bed Ladder Rack - Aluminum - 500 lbs #A99ZR would work great for your vehicle as long as it has the 5'…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...