Recommended King Pin Tripod Stabilizer For A Grand Design Reflection 150 Series 29RL

Question

Question:

Which fifth wheel tripod/camper jack would be best for a grand design reflection 150 series 29rl

asked by: Terry S

0

Expert Reply:

I recommend the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer # UF19-950001 for your Grand Design Reflection 150 Series 29RL.

This tripod has a weight capacity of 5,000-ls, which should be more than enough to support the pin weight of your Grand Design Reflection.

This tripod extends from 37" to 50" to give you plenty of range in height. Additionally, if desired, you could also use the Leg Extensions for Ultra-Fab 5th Wheel Kin Pin Tripod Stabilizer # UF19-950002, which will give you an additional 8" in height.

expert reply by: Bryce D

0

Answer 1

Yes, the JT Strong Arm Stabilizer System #LC191023 will work with your LCI Level Up System. I checked with Lippert and found that you can use the JT's Strong Arm Jack Stabilizer Kit #LC191023 with the adapter lugs #LC314592. For your LCI level up…

view full answer...

Answer 2

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 3

If the B and W Companion hitch is the #BWRVK3600 which fits the OEM rail kit of a Ram truck it can be used with a pivoting pin box like the Turning Point but if the hitch attaches to a gooseneck hitch via a center post then it can not be used with it…

view full answer...

Answer 4

Yes, we have two hitches that fit your 2020 Ford F-250; the Draw Tite part #65076 and the Curt #C31078. The difference is that the Curt will not stick out far past the air dam. I have attached a picture of the Curt showing this. Also the Curt is made…

view full answer...

Answer 5

We've checked in the past and have determined that the Grand Design Solitude 375 uses the Lippert 1621 pin box which the fifth wheel tripod you referenced part #UF19-950001 would easily work great with as the 1621 is the most common pin box out…

view full answer...

Answer 6

You might not notice as much of difference adding the MORryde Hitch Mounted Stabilizer for 2" Trailer Hitches #MR22AR since you stated your stabilizers are close by but you'd still be adding more support for your 2011 Keystone Montana…

view full answer...

Answer 7

Your 2018 Grand Design Reflection 150 has a Lippert 1621 style pivoting pin box which is the Sidewinder/Revolution part #RP34FR. If you wanted to replace that with the 5th Airborne part #RP78FR you mentioned this would be the correct fit.

view full answer...

Answer 8

The Ultra-Fab 5th Wheel King Pin Tripod Stabilizer - Steel - 37" to 50" - 5,000 lbs #UF19-950001 are great for taking away the bounce/sway and can be used with your auto-leveling 5th wheel especially the bounce in the space over the king…

view full answer...

Answer 9

The Ultra-Fab 5th Wheel Tripod Stabilizer #UF19-950001 is designed for stabilization and not truly to hold a load on its' own. I really like these as stabilizers but I don't believe I would trust them to hold a load while I make repairs to my…

view full answer...

Answer 10

You can change out your Lippert Turning Point pin box for the Trailair Air Ride 5th Wheel Pin Box - Lippert 1621 & 1621HD - 21,000 lbs #LC158778 as long as the mounting points are the same and you are within the capacity of your pin box. I've…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...