Installing JT Strongarm Stabilizer on a 16 Grand Design Reflections 337RLS 5th Wheel w/4 pt Leveling

Question

Question:

I want to install a JT strong arm stabilizer system but there is no documentation on how you install on the rear hydraulic rams. Will this system work with my LCI level up system 2016 Grand Design Reflections 337RLS fifth wheel with 4 point leaving

asked by: Mark R

0

Expert Reply:

Yes, the JT Strong Arm Stabilizer System # LC191023 will work with your LCI Level Up System.

I checked with Lippert and found that you can use the JT's Strong Arm Jack Stabilizer Kit # LC191023 with the adapter lugs # LC314592. For your LCI level up system will need a quantity of 6 adapter lugs, these are sold as a quantity of 2 on our site. The manufacture also provided me with instructions I will be sending you in a separate email.

I have linked the adapter lugs to this page for your convenience.

expert reply by: Jackie C

0

Robert

7/25/2020

Can the JT Strongarm stabilizers be used on a grand design 303 2019? Can you send directions if so? Thanks

Reply

Chris R.

7/29/2020

As long as you have more than 58" of space between the front landing gear legs on your Grand Design trailer, the JT's Strong Arm Jack Stabilizer # LC191023 will work great. We don't have install instructions specific for your trailer, but the primary manual is attached on the product page.

Reply

Answer 1

If the B and W Companion hitch is the #BWRVK3600 which fits the OEM rail kit of a Ram truck it can be used with a pivoting pin box like the Turning Point but if the hitch attaches to a gooseneck hitch via a center post then it can not be used with it…

view full answer...

Answer 2

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 3

I recommend the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer #UF19-950001 for your Grand Design Reflection 150 Series 29RL. This tripod has a weight capacity of 5,000-ls, which should be more than enough to support the pin weight of your Grand…

view full answer...

Answer 4

The people at B&W made removing and re-installing the B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3500 very easy. All you will need to do to remove it is take the head off of the assembly, as that will make the base…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 9

The safe GVWR rating is 80-85% of total weight capacity to allow for any additional weight added to the trailer. So for a 16k pin box you'd be looking at 12,800lbs - 13,600lbs as a safe weight. I looked up your current pin box with the LCI Number…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 12

While the best and most certain way to tell if your 2018 Ford F-250 has the puck system is to call your local Ford dealer with your VIN, it should be pretty easy to tell otherwise. If your bed looks like the accompanying photo - with four accessible…

view full answer...

Installing JT Strongarm Stabilizer on a 16 Grand Design Reflections 337RLS 5th Wheel w/4 pt Leveling

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching