Fit of Reese RP19315 High-Rise Gooseneck Ball in Factory Gooseneck Hitch on 2020 Ram 3500

Question

Question:

Will this fit my 2020 ram 3500 w/ factory prep for goose. I use the curt oem package from you guys. But need a little more height for my truck. My goose box hits a little and hitch is maxed out in heaight

asked by: Tom C

0

Expert Reply:

According to the folks at Reese, their # RP19315 High-Rise Pop In gooseneck ball works with both the Ford and the Ram OEM gooseneck hitch. The # RP19315 will offer a 1 inch height increase over the ball included with your OEM hitch so it will provide additional height for you.

I've linked to a demonstration video for the # RP19315 gooseneck ball.

expert reply by: Mike L

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Hey Eric, the Curt Multi-Fit Ball Kit w/ 4" Offset for Chevy/Ford/GMC/Nissan Underbed Gooseneck Hitch #C68ZV is not going to work with your Ram, unfortunately. This one is only going to work for select YMM (Year Make Model) Ford 250-450s, GMC…

view full answer...

Answer 4

The one really big downside to gooseneck towing is that there isn't a great solution for short bed truck clearance unlike fifth wheel towing. With fifth wheel hitches you can use a slider hitch and have the clearance issue handled. With gooseneck…

view full answer...

Answer 5

Yes, it will! The 5" Offset Gen-Y Hitch Gooseneck Trailer Hitch item #GY43XR is specially designed to work with the Ford factory puck system. It will push the connection point for the gooseball and your cattle trailer back 5" towards your…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The best way to prevent any clearance issues with your 2022 KZ Durango Gold G356RLQ and your 2020 Chevrolet Silverado 2500 with 6-1/2' bed and factory puck system is by using the Demco Autoslide 5th Wheel Hitch #DM79GV. This hitch slides back and…

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...

Answer 10

Yes, since the Gen-Y Hitch Gooseneck Trailer Hitch for Ford OEM Puck Systems #GY43XR has a 5" offset it will place the pin weight 2-1/2" behind the current center of your gooseneck hitch ball. This does means the front axle will be prone to…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

It is certainly possible for the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY58GR to work on your 2020 Ford F-250 Super Duty short bed, but there are likely going to be clearance issues as these are meant for long bed trucks. That…

view full answer...