Dimensions of the Deluxe Power Puller

Question

Question:

Can you tell me the overall length of the winch and handle in a storage position of the power puller winch, part # PTW4004DB?

asked by: Dennis C

0

Expert Reply:

The dimensions of the Deluxe Power Puller - 3 Hook - 8,000 lbs item # PTW4004DB are 29-1/2" x 4-1/4" x 6-1/2".

expert reply by: Jerred H

0

Answer 1

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms…

view full answer...

Answer 2

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of the…

view full answer...

Answer 5

Let's start at the brake assemblies/hubs on your new gooseneck trailer. The two wires coming from each assembly look exactly as they should. One wire will ground to the trailer frame and the other wire will attach to the brake output wire. The…

view full answer...

Answer 6

You could certainly use Opti-Brite LED work light #TLL48FB on your horse trailer and put it on a switch but having it wired into the running light circuit could have some unintended issues. Specifically, if you forgot to turn the switch off and drove…

view full answer...

Answer 7

Your slide-in truck camper does not have electric brakes so the blue brake circuit wire from its 7-way connector is not used. All other lighting functions as well as 12V auxiliary power will be maintained on the other circuits. Please refer to the…

view full answer...

Answer 8

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 11

The thread size is 3/8"-24 but the fitting size is 3/16". This standard for trailer brake lines. This will go from 1/2 inch thread size to 3/8 inch. If the dimensions you took are 1/2 inch and 3/8 inch of the threads this will fit.

view full answer...

Answer 12

The kit you are looking for is the part #BRKH10B which is nuts and lock washers needed to install the brake assemblies part #AKEBRK-35-SA that you referenced. The nut size is 7/16-20.

view full answer...

Dimensions of the Deluxe Power Puller

Product Page this Question was Asked From

Continue Researching