Replacement For A 1-065-041012-01 Landing Gear Motor

Question

Question:

Customer has a 2011 Primetime Crusader motor #1-065-041012-01 and needs a replacement does the LC141893 work for replacement

asked by: Jessica C

0

Expert Reply:

Yes, according to Lippert the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 would be a compatible replacement for your 1-065-041012-01 motor.

expert reply by: Kevin C

0

Answer 1

The correct replacement motor is part #LG-142178, and the Replacement Aluminum Gearbox, #LG-179015. The correct replacement switch is the part #LG-145236.

view full answer...

Answer 2

You should need repair kit #LG-146059 for the lead leg and #LG-146060 for the follower leg. From the picture you sent in I was able to determine that you have a Venture landing gear set VMC900R.

view full answer...

Answer 3

I attached a diagram that shows how the Lippert Components Venture Lead Leg Repair Kit #LG-146059 installs.

view full answer...

Answer 4

The Replacement Motor part #LG-196308 will be a direct fit for Stromberg Carlson, Venture, and Lippert (LCI) electric landing gear sets. It uses a direct drive system which will reduce strain on your jack and eliminate the need for a clutch. It is…

view full answer...

Answer 5

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 6

Yes you can just purchase the motor, in this case for your Lippert Model 1-065-041012-01, would be the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. This motor has a maximum load capacity of 5,000lbs and is rated for…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Replacement For A 1-065-041012-01 Landing Gear Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching