Replacement 72 Inch Fender for Tandem Axle Trailer

Question

Question:

I am looking for a steel tear fender 12 inches wide, 72 inches length and 20 inches high.

asked by: Jeff N

0

Expert Reply:

The closest fender that we have to match your description is the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers # HP74VR which measures 72" long x 10-3/4" wide x 20-1/2" tall. This is the widest fender that we carry and it is compatible with 15" and 16" wheels so if that matches what you have then this should still work.

I have attached a link to our selection of 72" long fenders as well as a review video of this fender set for you to check out.

expert reply by: Jon G

0

Answer 1

We may have something that works for you with fenders that have a very similar measurement to your 72" Long x 20" Tall x 10" Wide, which are fenders that measure 72" long x 10-3/4" wide x 20-1/2" tall: - Tandem Axle…

view full answer...

Answer 2

It sounds like you have good measurements for your current fenders that will help to narrow down with the fenders we have available. I do recommend checking the clearances on your current fenders to ensure that the new fenders will still have…

view full answer...

Answer 3

We have the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers #HP74VR that is 72" long, 10-3/4" wide and 20-1/2" tall. The Backing Plate #HP92FR is the matching backing plate for these fenders. Be sure to order 2 backing…

view full answer...

Answer 4

The Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers item #HP74VR you were looking at can be bolted to the side of your trailer. They can also be welded on. I have linked an installation video below.

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Replacement 72 Inch Fender for Tandem Axle Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching