Can I Bolt on the Tandem Axle Teardrop Trailer Fenders?

Question

Question:

i am looking at your trailer fenders and I have 1 question on the 72 x 16 Tandem finders can I bolt them right to the bed of the trailer?

asked by: Chris S

0

Expert Reply:

The Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers item # HP74VR you were looking at can be bolted to the side of your trailer. They can also be welded on. I have linked an installation video below.

expert reply by: Jerred H

0

Answer 1

We have the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers #HP74VR that is 72" long, 10-3/4" wide and 20-1/2" tall. The Backing Plate #HP92FR is the matching backing plate for these fenders. Be sure to order 2 backing…

view full answer...

Answer 2

It sounds like you have good measurements for your current fenders that will help to narrow down with the fenders we have available. I do recommend checking the clearances on your current fenders to ensure that the new fenders will still have…

view full answer...

Answer 3

The closest fender that we have to match your description is the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers #HP74VR which measures 72" long x 10-3/4" wide x 20-1/2" tall. This is the widest fender that we carry and it…

view full answer...

Answer 4

Although this replacement part looks a little different than your OEM 7-way connector socket, the Pollak Replacement 7-way, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for your Pollak PA66-MD40. This replacement…

view full answer...

Answer 5

We may have something that works for you with fenders that have a very similar measurement to your 72" Long x 20" Tall x 10" Wide, which are fenders that measure 72" long x 10-3/4" wide x 20-1/2" tall: - Tandem Axle…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...