Replacement Wheel Hub Cover For A 2007 Jayco Seneca With 19.5 Alcoa Wheels

Question

Question:

I have a 2007 Jayco Seneca with 19.5 Alcoa wheels. I lost a rear hub cap. I see you have the replacement with #PXQ822R or PXQ820R. How do I know what size lug nut and stud I have? Thanks for your help.

asked by: Mark

0

Expert Reply:

The stud doesn't matter when it comes to the wheel cap, you just need to measure the width of the lug nut to ensure the Phoenix USA Rear Hub Cover w/ Pop Out # PXQ822R or Phoenix USA Rear Hub Cover w/ Pop Out # PXQ820R will fit the lug nut.

The # PXQ822R is going to fit 33mm lug nuts and the # PXQ820R is going to fit 30mm lug nuts.

expert reply by: Kevin C

0

Answer 1

The Phoenix USA Front Hub Cover w/ Pop Out - 8 on 275mm - 30mm Lug Nuts - ABS Plastic, part #PXQ820F, you attached to your question will work for your wheels if they are 19-1/2" with an 8 on 275 mm bolt pattern. In order to get you the…

view full answer...

Answer 2

Yes the Demco Kar Kaddy SS Tow Dolly part #DM9713045 will work great with both your 2022 Hyundai Kona Limited FWD and your Winnebago Intent motorhome. It can be shipped to your home as well.

view full answer...

Answer 3

I reached out to Phoenix USA and was able to determine that the center cap of the Phoenix USA Rear Hub Cover #PXQ820R is part #PHX59FR.

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub…

view full answer...

Answer 6

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 7

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 8

While trailer axles do feature an upward bend like you are describing, there isn't a particular amount/measurement that is standard across the board. This bend in the axle is designed so that it will straighten under a trailer's loaded…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

The overall size of the Furrion Over the Range RV Convection Microwave part#FMCM15SS is 29-15/16" wide x 16-3/8" tall x 15" deep and requires a 30" cutout. If this matches the opening and size of the model you have this will be a…

view full answer...

Replacement Wheel Hub Cover For A 2007 Jayco Seneca With 19.5 Alcoa Wheels

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching