Replacement Wheel Cover For A 2006 Chevrolet Kodaiak

Question

Question:

Need to replace a wheel cover for a 2006 c5500

asked by: Roger

0

Expert Reply:

The Phoenix USA Front Hub Cover w/ Pop Out - 8 on 275mm - 30mm Lug Nuts - ABS Plastic, part # PXQ820F, you attached to your question will work for your wheels if they are 19-1/2" with an 8 on 275 mm bolt pattern. In order to get you the correct size wheel cover I will need your wheel size and your bolt pattern. Once I have this information I can recommend a replacement wheel cover for you.

I have included a video demo review and a weblink of how the measure bolt pattern of your wheel below.

expert reply by: Mark Smith

0

Answer 1

In order to confirm whether the Phoenix USA Front Hub Cover #PXQ820F fits your 8-lug pattern with 30mm nuts, you need to first make sure that you have a bolt pattern of 8 on 275mm. This is the bolt pattern that the #PXQ820F is designed to fit. The…

view full answer...

Answer 2

The Phoenix USA Front Hub Cover w/ Pop Out #PXQ820F are designed to fit 19.5" wheels but you will need to verify the bolt pattern and lug nut size of your Alcoa Wheels. This hub cover fits an 8 on 275mm bolt pattern and 30mm lug nut size.…

view full answer...

Answer 3

The stud doesn't matter when it comes to the wheel cap, you just need to measure the width of the lug nut to ensure the Phoenix USA Rear Hub Cover w/ Pop Out #PXQ822R or Phoenix USA Rear Hub Cover w/ Pop Out #PXQ820R will fit the lug nut. The…

view full answer...

Answer 4

Yes the Demco Kar Kaddy SS Tow Dolly part #DM9713045 will work great with both your 2022 Hyundai Kona Limited FWD and your Winnebago Intent motorhome. It can be shipped to your home as well.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...