Torque Value of Kingpin Coupler Set Screws for Andersen Ultimate Connection

Question

Question:

What should the 4 bolts on the King Pin coupler Block be torqued at ? Thanks

asked by: Ken W

0

Expert Reply:

For the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter, the kingpin coupler set screws, please note the linked instructions below.

expert reply by: Michael R

0

AM3200_001
(click to enlarge)

Answer 1

Pin box bolt torque is based on the size of the bolts. 1/2 inch Bolts GR5 90 ft-lbs 5/8 inch Bolts GR5 150 ft-lbs 3/4 inch Bolts GR5 275 ft-lbs

view full answer...

Answer 2

In regards to the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter part #AM3200, the four kingpin coupler set screws will need to be torqued to 40 ft. lbs. per the manual. The kingpin coupler will need to be center on the…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 8

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Torque Value of Kingpin Coupler Set Screws for Andersen Ultimate Connection

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching