Diameter of 3,500 lb Dexter Trailer Axle 35545I-ST-89

Question

Question:

What diameter is this axle pipe?

asked by: Manuel G

0

Expert Reply:

Axles that are 3,500 lbs are all 2-3/8 inches in diameter, and that is the diameter of the 3,500 lb Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs # 35545I-ST-89.

expert reply by: Kyle S

0

Answer 1

The pin in the Etrailer Weld-On Swivel Jack, #TJP-2001-B, measures 1/2 inch. The attached photo shows more dimensions of this jack for you to review.

view full answer...

Answer 2

The ThinLine LED Trailer Tail Light part #STL64RCB when used as an identification light at the top of a trailer over 80" wide will only need to serve one function which is to act as a marker/clearance light. Therefore, there will only be…

view full answer...

Answer 3

While I appreciate your ingenuity, you cannot install the light brackets in reverse so the license plate is on the right-hand (passenger's side) when installing the tail light assemblies of the Detail K2 Mighty Multi A-Frame Utility Trailer…

view full answer...

Answer 4

The Optronics LED Trailer Tail Light #STL9RB can be mounted however you would like. So there's nothing that will prevent the light from working. However, I would suggest checking with the DOT in your area to make sure that there aren't any…

view full answer...

Answer 5

I recommend using something like and L-bracket, such as #CE26098G, that you can attach to the top rail near the end of the trailer. Then you can attach a bracket such as #LPL55CB (may have to do some drilling/modify the L-bracket). Then you can…

view full answer...

Answer 6

The crossbars on the Erickson Truck Bed Ladder Rack - 500 lbs #EM07706 measure 1.8" in diameter. We have reached out and confirmed this with Erickson in the past. Attached is a review video for you to check out.

view full answer...

Answer 7

It looks like a Hayes Brake magnet part number 73400. We do not carry this part but I did a quick internet search and was able to find a couple places that sell them. From the research I did it looks like this is an older style of brake magnet used…

view full answer...

Answer 8

You have a typical 3500 lb brake hub/drum. The correct replacement drum would be #84546UC3 for standard spindles or #84546UC3-EZ for an E-Z Lube spindle. The hubs include the inner and outer wheel bearing, inner and outer races, the grease seal, dust…

view full answer...

Answer 9

I would begin by inspecting the magnets on the trailer brakes. If the magnets have windings or wear marks, the magnets are bad and will need to be replaced. You would need to match up your brake assembly size for the correct replacement magnet. The…

view full answer...

Answer 10

If the brake magnet is worn to the point that the windings are visible then you know it's time to replace the magnet. However, magnets can also fail without the visible signs of wear. Check out the FAQ article I attached on testing brake magnets…

view full answer...

Answer 11

A 14 inch trailer tire is going to be about 6 inches taller than what you have now so you'd lose about 3 inches of fender clearance. A 205/75-14 like the wheel and tire #AM32156 would have the same width so it would fit in that regard. We…

view full answer...

Answer 12

It sounds like you have a single axle trailer and are curious about whether or not to put the hanger like the part #28-5 or a shackle in front on the trailer frame. We recommend you put the hanger in the front. The force from the bumps in the road…

view full answer...

Diameter of 3,500 lb Dexter Trailer Axle 35545I-ST-89

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching