Torklift Camper Tie Downs that Fit 2013 Ford F-250 Long Bed with Factory Hitch

Question

Question:

i am looking for front and rear tie downs for a 2013 f250SD lariat. it has an 8 foot box with factory hitch and the running boards stop at the end of the cab. Thanks

asked by: Matt

0

Expert Reply:

For your 2013 Ford F-250 long bed that has the factory hitch and steps that are not underneath the bed you'd need the Torklift tie downs part # TLF2016 and # TLF3006 and you'd be set.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 3

I went ahead and reached out to Torklift, and they confirmed what you need to in order to remove the gas tank cover on your vehicle to install the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLF2016. The cover drops down and gives you…

view full answer...

Answer 4

Hey Bob, the Torklift Talon tie downs part #TL73QR weighs 35 lb. The TorkLift Talon Camper Tie-Downs #TL44XR weigh 26 lb. TorkLift Locking FastGun Turnbuckles #TLS9529-2-LK weighs 20 lb.

view full answer...

Answer 5

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 6

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 7

For your 2007 Dodge Ram 3500 Dually with an 8' bed I recommend the HappiJac Truck-Mounted Camper Tie-Downs #LC182908-182928 you were already looking at along with some turnbuckles like the #LC182898. These camper tie-downs permanently mount to…

view full answer...

Answer 8

Using an additional extender, like part #HE12, is very different than the rack, like part #K2TMC201, having a lengthy shank. The extenders like part #HE12 are usually made of two different sized pieces of steel that are welded together. The HE12 uses…

view full answer...

Answer 9

The only hitch extension we offer that is compatible with weight distribution hitches is the Titan Hitch Box Extension and Reducer #RP45292. This product is designed to fit hitches with a 2-1/2 inch receiver opening and then reduces down to a 2 inch…

view full answer...

Answer 10

For your 2008 Ford F-250 with a 6-3/4' bed you'll need the TorkLift Camper Tie-Downs - Front #TLF2012 and Rear #TLF3004. If you have running boards or steps that extend under the bed then you'll need to remove them in order to fit the…

view full answer...

Torklift Camper Tie Downs that Fit 2013 Ford F-250 Long Bed with Factory Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching