What Size Hole Is Required To Mount The Brophy # RR05 Recessed 5K Trailer Tie-Down D-Ring
Question:
What size hole saw is required to mount these in the trailer floor? Thx
asked by: Dennis
Helpful Expert Reply:
In order to mount the Brophy Recessed Trailer Tie-Down D-Ring # RR05, you will need a hole that is 3-3/8 inches in diameter. We recommend you use the backing plate system if you are not attaching this to either a trailer framer or trailer with a steel bed.The Brophy # RR5K includes the backing plate and all necessary hardware.
I have attached a short video showing an installation of the tie-down kit.
Products Referenced in This Question
Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 1600 lbs
- D-Ring
- Surface Mount - Bolt-On
- Brophy
more information >
Product Page this Question was Asked From
Brophy D-Ring Tie Down Anchor - Bolt-On - 4-7/8" Wide - Recessed Mount - 1,600 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 1600 lbs
- D-Ring
- Recessed Mount
- Brophy
more information >
Continue Researching
- Article: Where to Position the Trailer Axle?
- Article: How to Wire an Electric Winch
- Search Results: receiver hitch tube
- Q&A: Is It Possible to Add an Axle to a Single Axle Trailer
- Search Results: weld on jack pipe mount
- Article: Trailer Hitch Receiver Sizes
- Article: Determining Trailer Tongue Weight
- Q&A: D-Ring and Backing Plate Recommendation without Hole Cut In Center
- Video: Review of etrailer Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks - TJP-FP58
- Video: Dutton-Lainson Trailer Winch DL24110 Review
- Video: Bulldog Trailer Jack BD500339 Review
- Search Results: d rings
- Search Results: trailer anchors
- Video: Buyers Products Tie Down Anchors - Trailer Tie-Down Anchors - 337B40 Review
- Video: Review of Durabilt Chain Tie Downs - DU85MR
- Video: Buyers Products Tie Down Anchors - Trailer Tie-Down Anchors - 3371901006 Review
- Video: Brophy Swiveling D-Ring Anchor with Backing Plate and Hardware Installation - Enclosed Trailer
- Shop: Brophy Swiveling D-Ring Anchors w Backing Plates and Hardware - Bolt-On - 2,000 lbs - Qty 4
- Shop: Buyers Products 5/8" Forged D-Ring With 4-Hole Integral Mounting Bracket
- Shop: Brophy D-Ring Tie Down Anchor - Bolt-On - 4-7/8" Wide - Recessed Mount - 1,600 lbs
- Shop: Gen-Y Weld-On 2" Receiver Tube - 5-1/2" Long - Steel
- Shop: Combo Bar 6" with 2" Trailer Hitch Receiver - Unpainted
- Shop: Combo Bar 12" with 2" Trailer Hitch Receiver - Unpainted
- Shop: Buyers Products Weld-On Receiver Tube with 2" Hitch Receiver - 8" Long - 20K
- Shop: Camper Tie-Downs
- Q&A: Size of Hole Saw to Use to Install the Recessed Trailer D-Ring Tie Down RR5K
- Q&A: Installing D-Ring Surface Mount Tie-Down Anchors on a Aluminum Snowmobile Trailer
- Q&A: Will a 3-1/4 Hole Saw be Enough for Installing Recessed Trailer D-Ring Tie Down # RR05
- Search Results: cargo d rings
- Search Results: motorcycle carrier