Size of Hole Saw to Use to Install the Recessed Trailer D-Ring Tie Down RR5K
Question:
I am installing the D rings in an enclosed trailer. The video states using a 3 1/4 inch hole saw blade to cut the hole into the plywood floor and then use a file bit to cut out a little more of the hole for the internal bolts of the d ring. I noticed the hole in the backing plate is actually 3 1/2 inch in diameter. Is that an error in the video or should you use a 3 1/4 inch hole saw blade... Will the d ring actually seat in the whole from the top side using a 3 1/4 in blade?? I have purchased the 3 1/4 inch blade to use but if I need a bigger size I want to return it before I use it and get the correct size. Thanks,
asked by: Dewayne
Expert Reply:
The 3-1/4 inch diameter hole to install the part # RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw.
I attached a link to the install video you mentioned as well.
Product Page this Question was Asked From
Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 1600 lbs
- D-Ring
- Surface Mount - Bolt-On
- Brophy
more information >
Continue Researching
- Shop: Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Search Results: recessed anchor point
- Video: Brophy D-Ring Tie Down Anchor with Backing Plate Review
- Q&A: How To Install The Brophy Trailer D-Ring Tie Down, # RR5K, On A Wood Trailer Floor
- Search Results: recessed tie down
- Video: Brophy Tie Down Anchors - Trailer Tie-Down Anchors - RR5K Review
- Shop: Brophy D-Ring Tie Down Anchor - Bolt-On - 4-7/8" Wide - Recessed Mount - 1,600 lbs
- Q&A: Recessed Trailer D-Ring Tie Down RR5K Measurements
- Search Results: bearing buddies
- Shop: Trailer Wheel Center Cap, Chrome, 4.25" Pilot Size
- Shop: Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.25" Pilot - Stainless Steel
- Shop: Lionshead Trailer Wheel Center Cap - 4.25" Pilot - Stainless Steel - Qty 1
- Shop: Uni-Lite LED Clearance and Side Marker Light w Grommet - Submersible - 2 Diodes - Clear Lens - Amber
- Shop: Uni-Lite LED Clearance or Side Marker Trailer Light - Submersible - Amber - 2 Diodes - Clear Lens
- Video: Brophy Swiveling D-Ring Anchor with Backing Plate and Hardware Installation - Enclosed Trailer
- Video: Brophy E-Track 5 Gallon Bucket Holder Review
- Video: Brophy Vertical Tool Holder for E-Track Review
- Video: Brophy E-Track Horizontal Pipe Holder Review
- Video: Brophy E Track - E-Track Cargo Organizers - ETVH Review
- Q&A: Tie-Downs to Secure UTV to Aluminum Trailer
- Q&A: What Size Hole Is Required To Mount The Brophy # RR05 Recessed 5K Trailer Tie-Down D-Ring
- Q&A: Installing D-Ring Surface Mount Tie-Down Anchors on a Aluminum Snowmobile Trailer
- Q&A: Is 3/4 Inch Plywood Floor Adequate for D-Ring Tie Down Anchors with Backing Plate for 3,000 lb Car
- Q&A: How to Charge a Trailer Battery Through a 7-Way Connector
- Search Results: motorcycle wheel chock
- Article: Determining Trailer Tongue Weight
- Shop: Trailer Wiring
- Article: How to Install E-Track in 3 Easy Steps
- Search Results: vent
- Search Results: d ring