Is Bolt Pattern between B and W Hitches BWHDRH25122 and BWHDRH25198 the Same

Question

Question:

I have a 97 f250 with regular bumper on it now. The previous owner had s flatbed on it and theres existing holes drilled for hitch. I was wondering if these two hitches have the same bolt hole measurements. I know one is for a deep bumper. BWHDRH25122 and BWHDRH25198

asked by: Dustin B

0

Expert Reply:

Since the only difference between the B and W Hitches # BWHDRH25122 and # BWHDRH25198 is the style of bumper they fit with the bolt pattern is the exact same. Only difference is the height difference relative to the hitch opening and where it mounts to truck frame.

expert reply by: Jameson C

0

Answer 1

According to B&W the side brackets are 6-1/4" tall for their Heavy-Duty Trailer Hitch Receiver #BWHDRH25124.

view full answer...

Answer 2

Yes, check out the picture I attached that has the vertical distances from where the hitch mounts to the frame of the vehicle down to the hitch tube. Since you need at least 6 inches this would clear that by 1-3/8 inches.

view full answer...

Answer 3

The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front holes- 28-7/8" -Middle and rear holes-…

view full answer...

Answer 4

I called my contact at B&W and she gave me the following measurements of their Class V Trailer Hitch #BWHDRH25122. From the rear bolt hole to the middle bolt hole is 11-3.8 inches. From the middle bolt hole to the front bolt hole is 5-15/16…

view full answer...

Answer 5

The #BWHDRH25122 has 35-5/8 inches between mounting holes like what you see in the picture I attached. Since you need larger than than let me know what vehicle you have and I can see which would be best fit.

view full answer...

Answer 6

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

view full answer...

Answer 7

The distance from the bottom of the frame to the top of the 2" receiver of the B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" #BWHDRH25198 you were looking at is 7-3/8" as shown in the included diagram. I…

view full answer...

Answer 8

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...

Answer 9

I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers. We have two bumpers that have been determined to be a fit…

view full answer...

Answer 10

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 11

The #BWHDRH25122 measures 5 inches from the frame to the top of the hitch receiver. The #BWHDRH25198 measures 7-3/8 inches from the frame to the top of the receiver.

view full answer...

Answer 12

We do offer a B&W hitch for your 2000 Chevy C/K Series truck. Due to the frame width you mention, you'd want to use the B&W Class V hitch, part #BWHDRH25124 which is designed for pickup trucks. The B&W Class V receiver hitch you…

view full answer...

Is Bolt Pattern between B and W Hitches BWHDRH25122 and BWHDRH25198 the Same

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching