Where Does Wiring Harness Plug Into on 2018 Ford Explorer

Question

Question:

2018 ford explorer wiring harness. the part 118540..its either super tight or i am doing it wrong. any help would be appreciated. does it plug into the cream color one or black on the car?

asked by: Jeremy B

0

Expert Reply:

I have added a photo for you of where on your 2018 Ford Explorer you should plug in the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118540.

The harness is black and will be up behind the rear wheel on the passenger's side. I have also added a link below to a video install of the # 118540 on an '18 Explorer.

expert reply by: Kyle S

0

Where to Plug In T-One 118540 on 2018 Ford Explorer
(click to enlarge)

Answer 1

The T-One Vehicle Wiring Harness #118410 is not going to drain the vehicle battery unless there is something plugged into the 4-Way that is drawing power. If the power wire for the harness is touching bare metal somewhere it could be shorting and…

view full answer...

Answer 2

Based on my research, the Explorers with a factory tow package came out of the factory with either a 7-way trailer connector or a 4-way connector. If you want a 4-way connector, I recommend using the Tow Ready T-One Vehicle Wiring Harness #118540. I…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...