Is There a Harness That Goes Between Truck and Trailer When Using Dutton-Lainson Electric Winch

Question

Question:

I bought the electrical package for the Dutton boat winch which I will attach to my pickup. Is there a pigtail that goes from the back of the pickup to the winch? If I use the 25 ft wire attached to pickup I have to coil up the extra length of wire. That doesnt make sense!

asked by: Cleon C

0

Expert Reply:

In regards to the Dutton-Lainson StrongArm Electric Winch part # DL25215, the winch wiring harness is designed to attach to a vehicle battery and then run from the front back to the bumper so you can attach to the winch on the trailer when needed. There will be extra wire that will be simply coiled up and stored on the truck while not in use. If you wanted to cut the wire at the bumper you could then make a quick-connect system between the truck and trailer using the extra wire and Dutton-Lainson Electrical Quick Connects part # DL24085.

expert reply by: Conner L

0

Answer 1

The Dutton-Lainson Electrical Quick Connect for TW4000 Electric Winches, #DL24086, accepts up to 10 gauge wire. To secure the wire, you will need to solder it into place as it cannot be crimped. This product is designed for use with TW4000 electric…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...