Correct Replacement for Lippert Ultra Light Stabilizer Jack Model 113407

Question

Question:

I need to replace both of my Lippert Ultra Light Stabilizer jacks Model 113407 on my Forest River Wildwood 32BHDS travel trailer. What do you recommend? Each unit has the black switch LC298707 that extends and retracts the jacks. I want to replace those also.

asked by: John R

0

Expert Reply:

The Lippert High-Speed Power Stabilizer Jack part # LC298707 is a direct fit replacement for the Lippert Ultra Light Stabilizer Jack Model 113407. It does come with a new switch so you can either wire the jacks up to the old switch or install a new one.

expert reply by: Conner L

0

Answer 1

The direct replacement for your Lippert Components model 113407 stabilizer jacks can be found with part #LC369774 on our site. My contact at Lippert confirmed that this is the correct replacement.

view full answer...

Answer 2

Sounds like you are looking for a replacement stabilizer jack for the Lippert set you have installed on your RV. The direct replacement for your Lippert Model 113407 stabilizer jack is part #LC369774. This is the new part number.

view full answer...

Answer 3

Yes, the Lippert Components High-Speed Power Stabilizer Jack #LC369774 comes with a manual override crank handle so in the event you lost power you could still operate them. I attached a review video for this kit for you to check out as well.

view full answer...

Answer 4

Thank you for the photo; you are going to need to replace your Lippert stabilizer jack 113407. The good news is we do carry the exact replacement, Lippert Components High-Speed Power Stabilizer Jack #LC369774.

view full answer...

Answer 5

I checked with Lippert and was able to verify that the exact replacement for your Lippert Model 113407 Stabilizer Jack is the Lippert Components High-Speed Power Stabilizer Jack #LC369774. This jack will bolt right up to the frame on your toy…

view full answer...

Answer 6

The Lippert Components High-Speed Power Stabilizer Jack #LC369774 is designed to mount to existing holes that are spaced apart by 68-11/16 inches on center. As long as your Northshore Toy Hauler features the necessary bolt hole spacing on the frame…

view full answer...

Answer 7

The best resource we can give you to help install the Lippert High-Speed Power Stabilizer Jack #LC369774 that you refernced would be to have you check out the install video we made when we had the chance to install this setup on a similar RV. The…

view full answer...

Answer 8

The Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift #LC369774 you were looking at will be an exact replacement for the Lippert Stabilizer Jack 113407 you have on your camper. You can reuse your current switch, or if it…

view full answer...

Answer 9

For your 2010 Springdale I suggest the Lippert Stabilizer Jacks #LC298707. This system bolts onto your trailer's frame and are equipped with a new motor that is twice as fast.

view full answer...

Answer 10

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 11

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 12

The 30" Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR have a weld on design. This is the only way to install the jacks with the included mounts as there is not enough room between the stabilizer itself and the mounting plate for additional…

view full answer...

Correct Replacement for Lippert Ultra Light Stabilizer Jack Model 113407

Product Page this Question was Asked From

Continue Researching