Replacement Stabilizer Jack for Lippert 113407 on Toy Hauler

Question

Question:

I would like to replace the rear stabilizing jack on my 2015 Forrest River WPT 28VFKS toy hauler. Attached are pictures. Is this model a direct bolt on replacement ?

asked by: Michael F

1

Helpful Expert Reply:

I checked with Lippert and was able to verify that the exact replacement for your Lippert Model 113407 Stabilizer Jack is the Lippert Components High-Speed Power Stabilizer Jack # LC369774. This jack will bolt right up to the frame on your toy hauler and features new patented technology with a motor that is 2 times faster than the original system.

I have attached the installation details that you can also take a look at.

expert reply by: Chris R

1

click to enlarge

Answer 1

Sounds like you are looking for a replacement stabilizer jack for the Lippert set you have installed on your RV. The direct replacement for your Lippert Model 113407 stabilizer jack is part #LC369774. This is the new part number.

view full answer...

Answer 2

The direct replacement for your Lippert Components model 113407 stabilizer jacks can be found with part #LC369774 on our site. My contact at Lippert confirmed that this is the correct replacement.

view full answer...

Answer 3

Yes, the Lippert Components High-Speed Power Stabilizer Jack #LC369774 comes with a manual override crank handle so in the event you lost power you could still operate them. I attached a review video for this kit for you to check out as well.

view full answer...

Answer 4

For your 2010 Springdale I suggest the Lippert Stabilizer Jacks #LC298707. This system bolts onto your trailer's frame and are equipped with a new motor that is twice as fast.

view full answer...

Answer 5

The best resource we can give you to help install the Lippert High-Speed Power Stabilizer Jack #LC369774 that you refernced would be to have you check out the install video we made when we had the chance to install this setup on a similar RV. The…

view full answer...

Answer 6

The Lippert High-Speed Power Stabilizer Jack part #LC298707 is a direct fit replacement for the Lippert Ultra Light Stabilizer Jack Model 113407. It does come with a new switch so you can either wire the jacks up to the old switch or install a new…

view full answer...

Answer 7

Thank you for the photo; you are going to need to replace your Lippert stabilizer jack 113407. The good news is we do carry the exact replacement, Lippert Components High-Speed Power Stabilizer Jack #LC369774.

view full answer...

Answer 8

The Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift #LC369774 you were looking at will be an exact replacement for the Lippert Stabilizer Jack 113407 you have on your camper. You can reuse your current switch, or if it is…

view full answer...

Answer 9

The Lippert Components High-Speed Power Stabilizer Jack #LC369774 is designed to mount to existing holes that are spaced apart by 68-11/16 inches on center. As long as your Northshore Toy Hauler features the necessary bolt hole spacing on the frame…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Replacement Stabilizer Jack for Lippert 113407 on Toy Hauler

Product Page this Question was Asked From

Continue Researching