Install Video for Lippert High Speed RV Stabilizer Jack # LC369774

Question

Question:

I recently bought a pair of electronic stabilization jacks for your web site,it did not come with wiring diagram and the only thing I found online the wire colors were different on extend / retract switch my colors are red, white, green and black can you help

asked by: John K

0

Expert Reply:

The best resource we can give you to help install the Lippert High-Speed Power Stabilizer Jack # LC369774 that you refernced would be to have you check out the install video we made when we had the chance to install this setup on a similar RV. The entire process including the wiring is covered. It's linked on this page for you to check out.

expert reply by: Jameson C

0

Answer 1

You will need to bolt on the Ultra-Fab Power Twin II Electric Stabilizer, #UF39-941705, using the included hardware. It bolts to the bottom of the frame on the travel trailer. You CAN do it. I believe in you. If you have the proper tools (drill,…

view full answer...

Answer 2

For your 2010 Springdale I suggest the Lippert Stabilizer Jacks #LC298707. This system bolts onto your trailer's frame and are equipped with a new motor that is twice as fast.

view full answer...

Answer 3

Thank you for the photo; you are going to need to replace your Lippert stabilizer jack 113407. The good news is we do carry the exact replacement, Lippert Components High-Speed Power Stabilizer Jack #LC369774.

view full answer...

Answer 4

The Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift #LC369774 you were looking at will be an exact replacement for the Lippert Stabilizer Jack 113407 you have on your camper. You can reuse your current switch, or if it is…

view full answer...

Answer 5

Yes, the Lippert Components High-Speed Power Stabilizer Jack #LC369774 comes with a manual override crank handle so in the event you lost power you could still operate them. I attached a review video for this kit for you to check out as well.

view full answer...

Answer 6

The Lippert High-Speed Power Stabilizer Jack part #LC298707 is a direct fit replacement for the Lippert Ultra Light Stabilizer Jack Model 113407. It does come with a new switch so you can either wire the jacks up to the old switch or install a new…

view full answer...

Answer 7

The Lippert Components High-Speed Power Stabilizer Jack #LC369774 is designed to mount to existing holes that are spaced apart by 68-11/16 inches on center. As long as your Northshore Toy Hauler features the necessary bolt hole spacing on the frame…

view full answer...

Answer 8

Sounds like you are looking for a replacement stabilizer jack for the Lippert set you have installed on your RV. The direct replacement for your Lippert Model 113407 stabilizer jack is part #LC369774. This is the new part number.

view full answer...

Answer 9

The direct replacement for your Lippert Components model 113407 stabilizer jacks can be found with part #LC369774 on our site. My contact at Lippert confirmed that this is the correct replacement.

view full answer...

Answer 10

I checked with Lippert and was able to verify that the exact replacement for your Lippert Model 113407 Stabilizer Jack is the Lippert Components High-Speed Power Stabilizer Jack #LC369774. This jack will bolt right up to the frame on your toy hauler…

view full answer...

Answer 11

Yes, you can still raise and lower Lippert Components Power Stabilizer Trailer Jack Item #LC298707 even if the switch goes bad or electrical power is lost for any reason. In order to operate the jack manually there are a few steps: First always…

view full answer...

Answer 12

The wiring of the Lippert Components High-Speed Power Stabilizer Jack #LC298707 that you referenced is the exact same for if used at the front or rear of an RV. I attached a diagram that shows how everything wires up for you to check out as well as…

view full answer...

Install Video for Lippert High Speed RV Stabilizer Jack # LC369774

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching