Diameter of Threaded Rod of Propane Tank Holder Mounting Kit for 20 lb Tanks

Question

Question:

Does this assembly have the 3/8 inch threaded rod or the 1/2 inch threaded rod. it says 1/2 inch hole but i dont want to to assume that means 1/2 inch rod

asked by: Paul S

0

Expert Reply:

Good question, and the threaded rod is 1/2 inch diameter for the propane tank mounting kit you asked about:

- Complete Propane Tank Holder Mounting Kit for 20 lb Tanks # 37220BL

This 1/2 inch diameter rod is also 17-1/2 inches in length.

expert reply by: Kyle S

0

Answer 1

The controller does have to be on; the Fogatti Tankless RV Water Heater #LSB44FR senses when the water lines coming into the heater have dropped to 35 degrees Fahrenheit and begins cycling warm/hot water through the lines to keep them from freezing.…

view full answer...

Answer 2

Our installers and customer experiences have led us to believe that the Furrion tankless heaters like the part #FR98SR are by far the best and most reliable so that is what I would recommend. Not saying that the Fogatti is a piece of junk but the…

view full answer...

Answer 3

The diameter of the replacement threaded rod part #37207-30525 that you referenced is 1/2 inch in diameter and has a thread pitch of 13 threads per inch.

view full answer...

Answer 4

For your 20 lb tanks you want to use the kit #37220BL instead of part #37230BL that you referenced. The only difference between these kits is the length of the threaded rod that the hold down bar and wingnut attached to. The shorter one is used for…

view full answer...

Answer 5

Yes, the U-Post RV LP Gas Regulator Bracket #37207-30405 will work with the Compact Low Pressure 2-Stage Automatic Changeover RV LP Gas Regulator #37207-31525. The bracket mounts onto the threaded rod such as the #37207-30515 for a 20 lb. tanks or…

view full answer...

Answer 6

Chaining 4 tanks together is not recommended. I instead would use two separate systems an you will want to make sure the two additional tanks can also sit upright and have proper ventilation. You can use base #37207-31535 for both or #CAM57236 for…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...