Depth of Derale Thermal Fan Clutch with Reverse Rotation D22140

Question

Question:

What is the distance from the fan mount to the clutch mount?

asked by: James L

1

Helpful Expert Reply:

In regards to the Derale Thermal Fan Clutch with Reverse Rotation part # D22140, the distance from the mounting surface to the end of the shaft is 1-13/16" and the distance from the mounting surface to the end of the clutch is 1-3/4". I went out to our warehouse to verify these dimensions for you.

expert reply by: Conner L

1

Depth of Derale Thermal Fan Clutch with Reverse Rotation D22140
(click to enlarge)

Answer 1

view full answer...

Answer 2

It sounds like you may have a connector on your truck bed camper that's similar to a hookup for a dryer. If that's the case we definitely don't have any adapters for it and you'll likely have a hard time finding one so…

view full answer...

Answer 3

I reached out to Derale, who as able to confirm for me that the pilot inner diameter was 5/8 inches of the Derale Thermal Fan Clutch with Reverse Rotation #D22140.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

Depth of Derale Thermal Fan Clutch with Reverse Rotation D22140

Product Page this Question was Asked From

Continue Researching