2018 Jayco Melbourne Power Leveling Jack Recommendations

Question

Question:

25foot 2018 Jayco Melbourne MH, bolt on Power leveling jack recommendations.

asked by: Michael C

0

Expert Reply:

For your 2018 Jayco Melbourne, I recommend the Ultra-Fab Power Twin II Electric Stabilizer part # UF39-941705. This leveling system works with frame rails spaced between 48" to 80" apart.

expert reply by: Jerred H

0

Answer 1

In regards to trailer scissor jacks like Leveling Scissor Jack #JSC-24-IND, these simply need to be bolted to the frame either at the front or the rear. I don't have installation advice on these for any one specific trailer but so long as you…

view full answer...

Answer 2

The Stromberg Carlson Leveling Scissor Jack Set #JSC-24 will do a really good job of helping to stabilize your boat trailer for the winter and they will be easier to operate than jack stands. It is important to note though that stabilizer scissor…

view full answer...

Answer 3

The Leveling Scissor Jack Set part #JSC-24 can be mounted on a motorhome yes. In regards to installation, the jack will need to be attached to a part of the frame but there aren't many other mounting restrictions. However, I do recommend you…

view full answer...

Answer 4

Yes, you can use a Leveling Scissor Jack Set #JSC-24 to stabilize your Class C motorhome without having to attach them to your frame. Some of the more popular options are the MORryde Hitch Mounted Trailer Stabilizer #MR22AR and Valterra Folding…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...