Can Ball Tension be Adjusted on CTA-280 Trailer Coupler

Question

Question:

Is there a way to adjust the ball tension when it developes play. Thanks

asked by: Bob S

0

Expert Reply:

There is no way to adjust the tension on the ball on the Trailer Coupler - Adjustable Channel Mount - Squeeze Latch - Black - 2-5/16" Ball - 15,000 lbs # CTA-280. There will always be some amount of play to allow for movement. If it was too tight the ball would not be able to move when turning or going over bumps which would cause other problems. If you find that there is excessive play between the coupler and the ball you need to replace the coupler.

expert reply by: Robin H

0

Answer 1

I have a solution for you, but the #AM20422 is a 15" x 5" wheel, which is going to be slightly too narrow for a 235/75/R15 tire. In order to fit a tire of that size you would need at least a 6" wide wheel like the #AM20522, but there…

view full answer...

Answer 2

I have included a link that includes the tires that we currently carry that will fit your 15 by 5 rim. Depending on your trailer capacity, you will need to select the correct load range tire to match. These tires will fit the rim that you specified,…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

I attached a link to this page that has the install instructions for the Axle Riser Kit #LC382741 that you referenced.

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...