Could Roadmaster Dual Hitch Adapter part # RM-77-2 be Used to Carry Motorcycle Carrier

Question

Question:

Question regarding the RM 077-2 .. Can the upper receiver hold a heavy enduro motorcycle plus it’s rack with the total weight of 400 lbs ?

asked by: Abutalib

1

Helpful Expert Reply:

The Roadmaster Dual Hitch Receiver Adapter for Tow Bars # RM-077-2 does have a 400 lb tongue weight capacity so as long as you stay under that you can do what you are wanting.

expert reply by: Jameson C

1

Answer 1

We may have an option for you, though only the top receiver of the Roadmaster Dual Hitch Receiver Adapter, 6" Drop/Rise #RM-077-6 can be used for accessories, so you won't be able to use the bottom for a carrier like the etrailer…

view full answer...

Answer 2

Although an adapter that raises the height of the receiver will definitely help with the clearance issue you are talking about with your 2018 ProMaster 2500 please note that any adapter like this will reduce the weight rating of your trailer hitch…

view full answer...

Answer 3

I have a recommendation as the Roadmaster High Low Adapter #RM-058-4 is only designed to be used with tow bars and not a motorcycle carrier. The Replacement Shank for Gen-Y Adjustable Ball Mount #325-GH-303 gives you 3 stacked receivers. This will…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

To flat tow your Ram 2500, you'll need a tow bar, base plates, safety cables, a wiring solution, a supplemental braking system and possibly a high/low adapter. I really like the equipment offered by Roadmaster, the quality and ease of use are…

view full answer...

Answer 8

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 9

The Dexstar Dual Wheel part #AM20783 and the Lionshead Steel Dual Wheel part #LHHA420 are two very similar wheels with a few key differences. They are both 16" diameter x 6" wide wheels with a 8 on 6-1/2" lug pattern. However, the…

view full answer...

Answer 10

In order to both carry bikes and flat-tow a vehicle at the same time, you'd need to use an adapter on the motorhomes hitch, I recommend the Roadmaster Dual Hitch Receiver Adapter like part #RM-077-2 as it's designed for this exact purpose. In…

view full answer...

Answer 11

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Answer 12

The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn. If the spindle uses a castle nut and cotter pin or tang nut, tighten the nut finger tight until it…

view full answer...

Could Roadmaster Dual Hitch Adapter part # RM-77-2 be Used to Carry Motorcycle Carrier

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching