Will the Hex Shaft # DL406102 work on a Worm Gear Hand Winch # DL11002

Question

Question:

Is this strap winch available with a HEX shaft P/N406102? Id like to use it with a 1/2inch drill to raise my dock for the winter.

asked by: Conrad

0

Expert Reply:

The Hex Shaft for Dutton-Lainson Worm Gear Winches # DL406102 that you referenced is designed to fit Dutton-Lainson worm gear winches so yes, it will work on the Worm Gear Hand Winch # DL11002 that you referenced. However, this product is designed to work with 5/8 inch sockets and would not work with your 1/2 inch socket.

You will need to order this product separately as it is not included with the # DL11002.

I attached an FAQ article on hand winches for you to check out also.

expert reply by: Jameson C

0

Answer 1

For a worm gear winch that you can use with a strap instead of a cable I recommend #DL11002. You could then use strap #DL24242. You will need to add the hex shaft, #DL406102, in place of the standard shaft to use a variable speed drill with the…

view full answer...

Answer 2

I recommend going with the winch you mentioned, the Dutton-Lainson Worm Gear Hand Winch with Hex Drive Handle #DL11004. It would work perfectly for your application and can be operated manually or with a power drill like you wanted. It also works…

view full answer...

Answer 3

The Dutton Lainson Hand Winch, model #DL15721 does not feature a free-wheel option. The handle can be turned counter clockwise to unwind the cable or strap. If the minimum operating weight (175 lbs) is not applied, the winch handle will become loose…

view full answer...

Answer 4

The capacity of the Dutton-Lainson Worm Gear Hand Winch #DL11004 that you referenced is 2,000 lbs so your 18 volt drill would easily be able to operate the winch to raise 2,000 lbs as long as you have a 5/8 inch socket.

view full answer...

Answer 5

We have exactly what you are looking for! The Dutton-Lainson Worm Gear Hand Winch #DL11004 has a hex drive topwind handle that you can operate by hand while it sits on the floor of your trailer or with a drill and a 5/8" socket. I recommend…

view full answer...

Answer 6

You can use Dutton-Lainson Worm Gear Hand Winch with Hex Drive Handle - 2,000 lbs Item #DL11004 for your utility trailer. If you do I strongly recommend using a drill to reel in the line or let it out (worm gear winches do not have a free-spool mode)…

view full answer...

Answer 7

I do have a solution for you, however the Dutton-Lainson Hand Winch #DL11004 referenced in your question is actually designed for use with a polyester strap and not cable. For the Dutton-Lainson 2,000 pound hex gear hand winch that uses cable you…

view full answer...

Answer 8

Pulling cars onto a trailer will undoubtedly require pulling the vehicle up an incline, which will add extra resistance to the equation. If you are pulling a rolling load, not dragging the car and no flat tires, up just a slight incline like a 3…

view full answer...

Answer 9

Yes, the Fulton High-Performance Brake Winch part #F143100 will work with the Universal Hand Winch Right Angle Mounting Bracket part #DL24110. I went out to our warehouse and test fit the two products together to confirm this for you. I have attached…

view full answer...

Answer 10

The type of manual winch I suggest for your car trailer is a worm gear type which prevents the car from rolling backwards even if you let go of the handle. Winch capacity for your application with a rolling load on an incline does not need be very…

view full answer...

Answer 11

The Pin #DL205246 is what must be removed to swap the Hex Shaft #DL406102 onto your Dutton-Lainson Hand Winch #DL10976. I recommend using a press tool to remove the pin rather than tapping out with a hammer. A press tool like a motorcycle chain…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Will the Hex Shaft # DL406102 work on a Worm Gear Hand Winch # DL11002

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching