How Does the Kickboard Attach to a Jackknife Sofa

Question

Question:

How do you mount a jackknife sofa kickboard to the box front?

asked by: Mary J

0

Expert Reply:

A kickboard, such as the Replacement Kickboard for Thomas Payne RV Jackknife Sofa - 62" # 195-000110, has brackets on the backside. These brackets easily slide on to the frame of the Jackknife Sofa.

expert reply by: Thomas M

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

How Does the Kickboard Attach to a Jackknife Sofa

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching