Adapter For Connecting 100lb Propane Tank to Generator

Question

Question:

I purchased a Tri fuel Firman generator and want to hook it up to a 100lb propane tank. The hose that came with the machine only screws onto smaller 30lb Tanks. Do you have the complete setup to accomplish this?

asked by: Conal

0

Expert Reply:

What I think you are saying is that you have the correct hose for connecting to your generator but you an adapter at the opposite end for mating the hose to a 100 lb. tank. I think what you are needing is the MB Sturgis Propane Adapter Fitting - Soft Nose POL x Type, # 204128-MBS. This lets you adapt a 100-lb propane cylinder fitting to a male Type 1 thread.

expert reply by: Michael R

0

Answer 1

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 2

To add a 100 lb tank to your two 30 lb tanks, I recommend the MB Sturgis Sturgi-Stay T-Fitting w Hose - Type 1 Valve - Quick Disconnect, Disposable Cylinder Ports #103615. This will allow you to connect the red fitting to one of your tanks and the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...

Answer 5

For your race trailer with aluminum roof panels it will seal on the edges with a Butyl Tape #AL64UV. Then you will use either a Non-Sag #AL33KV or Self-Leveling #AL68KV sealant to seal the mounting screws and edges of the aluminum roof panels to…

view full answer...

Answer 6

Your Dometic 57915.531 is a 13.5k BTU AC unit which the Advent Air RV AC Unit #ACDOM135 is the same size and is also designed to replace Dometic units.

view full answer...

Answer 7

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I recommend the Alpha Systems Butyl Tape for RV Weatherproofing #AL28FJ as it's 1" wide to fully cover the flange of your vent. Make sure you overlap the ends to form a tight waterproof seal. You can see me doing this at 2:50 mark in the…

view full answer...

Answer 10

To add a in-bed 7-way to your 2024 Chevy Silverado 2500 to make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item #C58FV. This harness puts a 4-way and 7-way…

view full answer...

Answer 11

Yes, you'd just need to reach out to a qualified welder and have them weld on spring seats like part #TRSS300 to the top side of the Trailer Axle Beam with Easy Grease Spindles #e45GR. It's super common to do for people who have an underslung…

view full answer...

Adapter For Connecting 100lb Propane Tank to Generator

Product Page this Question was Asked From

Continue Researching